Timer Module, Timer Switch Module, DC 6V-30V Trigger On/Off Cycle Timing Delay Switch, Adjustable LED Display Automation Digital Delay Timer Module Micro USB 5V

$20.99

  • [Wide Voltage Compatibility] Wide dc power supply voltage from 6V to 30V, supporting micro USB 5.0V power supply for convenience. Load Capacity: DC 30V 5A, AC 220V 5A, Quiescent Current: 20mA, Operating Current: 50mA, Operating Temperature: -40~85
  • [Intuitive Interface] DC 6V-30V trigger delay On/Off cycle timer relay switch module features LED digital dispaly. Clear, simple, and powerful interface, meeting all your needs with ease of use.
  • [Enhanced Sleep Mode] Automatically turns off display after 5 minutes of inactivity, easily wake up with any button press. C-P sleep mode: if no operation within 5 minutes; display will close automatically while procedure runs normally. O-d normal mode: displays always shows. Press and hold STOP button for 2 seconds to change between C-P and O-d, present state will flash and then back to the main interface.
  • [Emergency Stop Function] Built-in STOP button for emergency situations, with reverse input protection for safety. Relay Enable Mode: 1. NO: Connection is allowed during OP time. 2. OFF: Connection is not allowed, always turned off. Press STOP button at main interface to change between ON and OFF, the present state will flash then back to main interface. (This is emergency stop function, used to disconnect relay.)
  • [Flexible Settings] Set different OP, CL, LOP parameters independently, automatically save settings in case of power failure, and improve anti-interference with optical coupling isolation. OP: Connect time. CL: Disconnect time. LOP: Loop times(1~999, “—” indicates infinite times). Press SET button at the main interface (display 000), it will show OP(CL, LOP) and corresponding time.

In stock

— OR  —

— OR  —

  • International Express shipping available
  • 30 day easy returns
Guaranteed Safe Checkout

Spec:
Voltage: 6V~30V(support micro USB 5.0V)
Trigger Signal Source: High voltage level trigger(3.0V~24V), signal ground and system ground are not connected to improve system anti-interference ability(or you can connect them).
Load Capacity: DC 30V 5A, AC 220V 5A
Quiescent Current: 20mA
Operating Current: 50mA
Operating Temperature: -40℃~85℃
Size: Approx. 6.2*3.8*1.7cm / 2.44*1.49*0.67″
Timing Range: 0.1seconds to 999 minutes(continuously adjustable)
Instruction:
Operation Mode:
P1: After triggering signal, switch is connected for “OP” time, then disconnected; within the “OP” time:
P1.1: if trigger signal again, it is invalid.

P1.2: if trigger signal again, restart timing.

P1.3: if trigger signal again, switch is disconnected, stop timing.
P-2: After triggering signal, switch is disconnected for “CL” time, then switch is connected for “OP” time, and disconnect after timing.
P3.1: After triggering signal, switch is connected for “OP” time, then switch is disconnected for “CL” time, and enter loop. If trigger signal during loop, switch is disconnected and stop timing. The loop times (LOP) can be set.
P3.2: After power on, no need trigger signal, switch will be connected for “OP” time, then disconnected for “CL” time, and enter loop. The loop times (LOP) can be set
P-4: Signal holding function. If there is trigger signal, timing will be reset, switch remains connected; when the signal disappears, it will disconnect after “OP” time. During timing, if there is a signal, timing will be reset.
OP: Connect time. CL: Disconnect time. LOP: Loop times(1~999, “—” indicates infinite times)
All above parameters are independent from each other, but all modes use the same parameters. For example, if set OP time as 5 seconds in P1.1, then change to P1.2, then the OP time in P1.2 will also be 5 seconds.

Additional information

Weight 0.03 kg
Brand

Estink

EAN

0794419555793

UPC

794419555793