Octopus V1.1 Board features:1. Support 3d printer: CR10 , Ender 3 , Ender 5 series, ect.2. Using high-performance MOSFET tube, better heat dissipation effect.3. Reserved dual Z-axis printer.4. Onboard EEPROM (AT24C32).5. Reserved WIFI interface (ESP8266), need firmware support.6. Reserve PT100 thermistor interface. Reserved for you, you can diy by yourself and use your imagination.7. Thermistor leakage protection, we have done an upgrade here to further protect the motherboard.8. Support Marlin and Klipper TOUCH1. An additional power supply may be needed in case your board does not supply enough current at 5V.2. Set Zmin pull-up on your firmware when using Logic Free (In most cases, it is already set up).3. If push-pin deploy fails, turn the core by up to 180 degrees with an Allen-key so that the core is further inside the casing.4. Depending on your type of 3D printer, you may need to remove or add some parts to the controller board.5. In principle, a controller board with a large capacitor in the end stop input circuit is not supported. (You may need to remove such a capacitor from your board)6. If noise, etc. interference is expected, you should use an anti-interference extension cable (Shielded or Twisted Cable).7. Electronic devices can be damaged or even destroyed if connected to the wrong side polarity.8. BIGTREETECH IS ONE OF THE DISTRIBUTORS OF ANTCLATS-BL TOUCH IN CHINABLTOUCH Specification1. Voltage / Current: 4.8 ~ 5.1 V2. Current: 15mA. Maximum (Peak): 300mA3. Z Probe Output: Logic Free (Open Drain: default) or 5V logic. Open Drain VDS / ID: Max VDS = 5V / Max ID = 300mA4. PCB / Soldering: OSP / Lead Free5. Cable Length: 150±5 mm (for retail)6. Weight: 0.35oz (10g)7. Wiring: 3Pin: Brown (GND), Red (+5V); Orange (control signal). 2Pin: Black (GND) White (Zmin)8. Case & Push-pin: Polycarbonate (PC)
BIGTREETECH for Creality Ender 3 Upgrade 3D Printer, Octopus V1.1 Motherboard with BL Touch Extension cable for Ender 3 v2 Ender 5 pro 3D Printers Support TFT70 TFT50 TFT43 Big Touch Screen
€250.99
- 1.【Powerful】Support 8 groups of stepper motor drives, 9 motor interfaces. It is convenient for you to choose the driver you want to use. The motherboard supports different types of drivers to work at the same time, you can experience the fun of DIY.
- 2.【Fast heat dissipation】Support 6 controllable fans, 2 normally open fans, each fan can independently select the power supply, and all support 5V, 12V, 24V. You can freely choose the fan model to facilitate your printing work. The Octopus board will dissipate heat faster and prolong its service life.
- 3.【High-quality protection】Designed and upgraded thermistor leakage protection to ensure the safety of the motherboard with high strength. You can rest assured to use the octopus board to print good-looking prints. Octopus Board the instruction manual and firmware: github/bigtreetech/BIGTREETECH-OCTOPUS-V1.0
- 4.【3DTouch is simple, smart, accurate】BLtouch-We has an official BLtouch authorizationuch is an auto leveling sensor for 3D Printers based on open-source. it allows you to accurately measure the inclination of your printing surface. greatly improve the printing accuracy of your 3D printer. High precision. The deviation of accurqcy is ±0.005mm. Simple, intelligent.
- 5.【BLTouch】BL touch-It can work with all kinds of bed materials such as glasses, wood, metal, etc. BL touch cable length: 150 mm, BLtouch Extension Wire length: 800mm. Voltage: 5 V. Current: 15 mA. Maximum (peak) current: 300 mA. PCB & Soldering: RoHS, lead free.
In stock
Additional information
| Weight | 0.34 kg |
|---|---|
| brand | BIGTREETECH |
| dimensions | 18.8 x 12.8 x 4.2 cm; 340 Grams |